Design and Performances of a Carbon Monoxide Sensor Using Mid-Infrared Absorption Spectroscopy Technique at 4.6 µm

Based on infrared absorption spectroscopy technique, a carbon monoxide sensor was developed using the fundamental absorption band of carbon monoxide molecule at the wavelength around 4.6 µm. The developed sensor consists of pulse-modulated wideband incandescence, open ellipsoid light-collector gas-cell, dual-channel detector, and control and signal-processing module. With the prepared standard carbon monoxide gas sample, sensing characteristics on carbon monoxide were investigated using the sensor. Experimental results reveal that the limit of detection is about 10 ppm, the relative error at the limit of detection point is less than 14%, and that is less than 7.8% within the low concentration range of 20～180 ppm. The maximum absolute errors of 50 min long-term measurement on the 0 and 14 ppm CO gas samples are about 3 and 3.17 ppm, respectively, and the standard deviations are as small as 0.18 and 1.25 ppm, respectively. Compared with the reported carbon monoxide detection systems utilizing quantum cascaded lasers and distributed feedback lasers, the proposed sensor shows potential applications in carbon monoxide detection under the circumstances of coal-mine and environmental protection, by virtue of high performance, low cost, simple optical structure, and so on.     

High frequency circular translation pin-on-disc wear testing of UHMWPE using a ball-on-flat contact along a hypotrochoidal track

To intensify experimental research within the field of orthopaedic tribology, a three-station, dual motion, high frequency (25.3 Hz) circular translation pin-on-disc wear test device was recently introduced. In the present study, the pins were CoCr with a spherical, polished bearing surface of 28 mm radius, whereas the flat discs were conventional UHMWPE. This configuration was intended to simulate the wear mechanisms of total knee prostheses. The number of wear cycles run was as high as 200 million. The mean wear rate was 0.35 mg per one million cycles (0.77 mg/24 h) which corresponded to a mean wear factor of 3.5 × 10⁻⁶ mm³/Nm. The study provided further proof that a wear test for orthopaedic implant materials can be accelerated by substantially increasing the cycle frequency, provided that the sliding velocity remains close to the values obtained from biomechanical studies. Hence, the moderate frictional heating will not lead to unrealistic wear mechanisms.     

Distorted wave response of ultrasonic annular stator incorporating non-uniform geometry

The traveling wave ultrasonic stator is normally fabricated with teeth. The tooth geometry improves the driving speed, but it creates natural frequency splitting and mode contamination, especially a distorted traveling wave. A dynamic model of a stepped-plate periodic stator is developed to examine the distortion. The stator is treated as an annular supported by a thin mid plate, and the support stiffness is formulated by using equivalent energy principle. The effects of the tooth and mid plate on the natural frequency and vibration mode are examined by using the perturbation method. The rules governing the frequency splitting, frequency perturbation as well as mode contamination are also identified. The traveling wave response and elliptical trace on stator surface are obtained by using the mode superposition method and they are proved to be distorted due to the tooth geometry. The response at the repeated doublets becomes coupled forward and backward traveling waves, but that at the split doublets becomes coupled forward traveling, standing and backward traveling waves. The results indicate that the tooth mass instead of the stiffness decreases the vibration amplitude and driving speed of the dominant wave, but their effects are different at the repeated and split doublets. Inspection of the model implies that the distortion can be suppressed by using a suitable combination of the wavenumber, tooth count, tooth height and occupying fraction. Numerical calculations are carried out to demonstrate the tooth geometry effect on the transient waveform, driving speed and elliptical trace. The optimization of the tooth geometry that can help achieve a purer traveling wave is discussed.     

Improved Self-Feedback Gain in the Context Layer of a Modified Elman Neural Network

The use of a range of values for the self-feedback gains in the context layer of a modified Elman neural network is shown to reduce RMS error when modelling a non-linear dynamic system.     

Electromechanical control of vibration on a plate submitted to a non-ideal excitation

This paper deals with the enhancement of electromechanical control of vibration on a thin plate submitted to non-ideal excitation. Modelling of the systems displays the non-ideal source used as external excitation above the structure on a particular surface and control force acting at specific points under the structure. The electromechanical device is composed by a RL circuit with a saturated inductance and stings connected to the plate is used as connection between the structure and the controller. Routh–Hurwitz criteria are used to obtain the stability condition of the controlled system and some dynamics exploration leads us to the condition for which the amplitude of vibration is reduced in the mechanical structure.     

Nonlinearity of muscle stiffness

In this letter, a comparison between three types (two linear and one nonlinear) of models of skeletal muscle stiffness is shown. Results are compared with experimental data for biceps brachii in the case of muscle stretching and with the Hill equation for a biological muscle. It is shown that results for nonlinear stiffness model in case of length-force relationship fits to the experimental data.     

On exponential stability analysis for neural networks with time-varying delays and general activation functions

This paper is concerned with the exponential stability analysis for a class of cellular neural networks with both interval time-varying delays and general activation functions. The boundedness assumption of the activation function is not required. The limitation on the derivative of time delay being less than one is relaxed and the lower bound of time-varying delay is not restricted to be zero. A new Lyapunov-Krasovskii functional involving more information on the state variables is established to derive a novel exponential stability criterion. The obtained condition shows potential advantages over the existing ones since no useful item is ignored throughout the estimate of upper bound of the derivative of Lyapunov functional. Finally, three numerical examples are included to illustrate the proposed design procedures and applications.     

Monostability,bistability, periodicity and chaos in gene regulatory network

This letter gives a general review on the monostability, bistability, periodicity and chaos in gene regulatory network. Some simple motifs that generate monostability, bistability, periodicity and chaos are analytically and numerically reported. Further research directions of the nonlinear dynamics of gene regulatory network are discussed.     

Grain-boundary states in solid oxide electrolyte ceramics processed using iron oxide sintering aids: a Mössbauer spectroscopy study

Journal of Solid State Electrochemistry - In order to appraise microstructure-determined defect formation processes and minor intergranular states in the solid electrolyte materials sintered...